xilinx USB Cable 找不到！

Pcbbar

驅動安裝結束，如下圖，下載器指示正常為綠燈，


8 M0 j6 ?8 e% q/ m, b- V  \" p
6 [# u$ c7 p, B! G
4 L$ q& q2 R7 a' J
/ {% H2 V/ L! ]進入IMPACT界面時，點擊PROGRAM出現如下錯誤：
+ [. W: ~* F: d# X8 }

- ^# [* O% q1 @6 AGUI --- Auto connect to cable...
INFO:iMPACT - Digilent Plugin: Plugin Version: 2.4.4
$ [" H. c  Q9 _$ O* ^2 W, PINFO:iMPACT - Digilent Plugin: no JTAG device was found.
; A1 w5 y8 \- \1 d1 N1 e- B0 RAutoDetecting cable. Please wait.
*** WARNING ***: When port is set to auto detect mode, cable speed is set to default 6 MHz regardless of explicit arguments supplied for setting the baud rates
PROGRESS_START - Starting Operation.
8 q) V  L. I0 u& q1 p5 J! t6 IConnecting to cable (Usb Port - USB21).
Checking cable driver.
Source driver files not found.
) o; z# ^6 g. KThe Platform Cable USB is not detected. Please connect a cable.If a cable is connected, please disconnect
3 T5 U- P* V# r9 P" s  T) @and reconnect to the usb port, follow the instructions in the 'Found New Hardware Wizard', then retry
" O/ n+ [. N6 C0 c# L& bthe Cable Setup operation.
Cable connection failed.
5 e) P9 }7 ]! `Connecting to cable (Parallel Port - LPT1).
7 }4 U3 X4 q) t: W; PChecking cable driver.
# p! U8 M/ I8 v* W4 m& b5 B' yYour driver installation is not complete. Please re-run your application or run
% l, e3 @7 c. L* g+ e: m- s1 Winstall_drivers.exe from the ISE installation area as an Administrator to complete the driver installation.
Service using windrvr6.sys : SYSTEM\CurrentControlSet\Services\WinDriver6.
ImagePath = \SystemRoot\system32\drivers\windrvr6.sys.
5 \3 e8 K7 C6 t) @" p! E Start = 3.
  F  D/ }( t2 F ErrorControl = 1.
9 q6 I5 C2 O$ x Type=1.
Cable connection failed.
0 k5 }2 U! w0 {) FConnecting to cable (Parallel Port - LPT2).
5 r5 c, b' y% vChecking cable driver.
* {2 I, G* ~$ v: HYour driver installation is not complete. Please re-run your application or run
install_drivers.exe from the ISE installation area as an Administrator to complete the driver installation.
6 l- A5 D* H2 ~/ OService using windrvr6.sys : SYSTEM\CurrentControlSet\Services\WinDriver6.
ImagePath = \SystemRoot\system32\drivers\windrvr6.sys.
4 F% F, \5 O& A* v! n( R Start = 3.
ErrorControl = 1.
+ Q+ G& B# i) [, T- W, V Type=1.
( u* r' c" m: XCable connection failed.
Connecting to cable (Parallel Port - LPT3).
Checking cable driver.
Your driver installation is not complete. Please re-run your application or run
install_drivers.exe from the ISE installation area as an Administrator to complete the driver installation.
4 O" }8 g* ^; p/ J- ]! h) KService using windrvr6.sys : SYSTEM\CurrentControlSet\Services\WinDriver6.
; t+ O, S: Z) G% E, x0 J5 Y ImagePath = \SystemRoot\system32\drivers\windrvr6.sys.
; q1 y* r, S) n$ x' G Start = 3.
; s! P% V# W  E6 ^8 q ErrorControl = 1.
Type=1.
Cable connection failed.
Connecting to cable (Parallel Port - LPT4).
Checking cable driver.
1 j. P1 w" g$ O: ^' Z$ ^9 j! T; RYour driver installation is not complete. Please re-run your application or run
' @) y3 l- c, Q2 ~: V9 J: `9 Ainstall_drivers.exe from the ISE installation area as an Administrator to complete the driver installation.
0 T" n/ N4 B7 m6 d8 A4 _* g0 \9 dService using windrvr6.sys : SYSTEM\CurrentControlSet\Services\WinDriver6.
ImagePath = \SystemRoot\system32\drivers\windrvr6.sys.
3 A$ {$ M: j  {3 t0 {- ~) I; |) l Start = 3.
5 d& H4 y! `4 N ErrorControl = 1.
8 x6 T! |, |7 X: m Type=1.
Cable connection failed.
PROGRESS_END - End Operation.
# A. x6 D, }9 m5 U: ]/ }  eElapsed time =      2 sec.
# c) f+ ^) i) w- I% tCable autodetection failed.
3 `+ [! x; f" A' o! K3 {/ rWARNING:iMPACT:923 - Can not find cable, check cable setup !
) Y% G7 O$ {/ n4 r! q
+ B$ T5 x' [4 g' i6 h
各位大神解圍，不勝感激！

PCB觀察

阿里電子

https://blog.csdn.net/qq_36775035/article/details/80714563

PCB觀察

經過了6天的摸索，終于成功了，祈禱，阿門！

Mira_PCB

樓主樓主，能問一下你是怎么解決的嗎

PCBQA

具體怎么解決，我跟你遇到的問題一模一樣，好些天都沒進展，麻煩你指導一下。
1 d- j- L0 D# ~

Pcbbar

重新安裝驅動

深度大腦

你好，我遇到了同樣的問題，也重新裝了ise自帶的驅動，仿真器的指示燈顯示正常（電路板不上電為橘黃色，上電是綠色），但是還是出現 你上述的問題。Can not find cable, check cable setup !
9 U& L- s% P# ~  I1 t* [* [8 k8 F9 I可否聯系一下；e-mail：144605975@qq.com

電子工科男

我遇到的問題是打開cable set界面會閃退
0 L8 ?3 Q) k6 `+ ^) b

larssix

77777777777777777777777